sram-techmanual-my10-gearhubsystems-english-reva.pdf

(31817 KB) Pobierz
01
(english)
technical manual
gear hub systems
SRAM® LLC WARRANTY
EXTENT OF LIMITED WARRANTY
SRAM warrants its products to be free from defects in materials or workmanship for a period of two years after
original purchase. This warranty only applies to the original owner and is not transferable. Claims under this
warranty must be made through the retailer where the bicycle or the SRAM component was purchased. Original
proof of purchase is required.
LOCAL LAW
This warranty statement gives the customer specific legal rights. The customer may also have other rights which
vary from state to state (USA), from province to province (Canada), and from country to country elsewhere in the
world.
To the extent that this warranty statement is inconsistent with the local law, this warranty shall be deemed modified
to be consistent with such law, under such local law, certain disclaimers and limitations of this warranty statement
may apply to the customer. For example, some states in the United States of America, as well as some governments
outside of the United States (including provinces in Canada) may:
a.
b.
Preclude the disclaimers and limitations of this warranty statement from limiting the statutory rights of the
consumer (e.g. United Kingdom).
Otherwise restrict the ability of a manufacturer to enforce such disclaimers or limitations.
LIMITATIONS OF LIABILITY
To the extent allowed by local law, except for the obligations specifically set forth in this warranty statement, in
no event shall SRAM or its third party supplies be liable for direct, indirect, special, incidental, or consequential
damages.
LIMITATIONS OF WARRANTY
This warranty does not apply to products that have been incorrectly installed and/or adjusted according to the
respective SRAM technical installation manual. The SRAM installation manuals can be found online at www.sram.
com, www.RockShox.com, or www.avidbike.com.
This warranty does not apply to damage to the product caused by a crash, impact, abuse of the product, non-
compliance with manufacturers specifications of usage or any other circumstances in which the product has been
subjected to forces or loads beyond its design.
This warranty does not apply when the product has been modified.
This warranty does not apply when the serial number or production code has been deliberately altered, defaced or
removed.
This warranty does not apply to normal wear and tear. Wear and tear parts are subject to damage as a result of
normal use, failure to service according to SRAM recommendations and/or riding or installation in conditions or
applications other than recommended.
Wear and tear parts are identified as:
• Dust seals
• Bushings
• Air sealing o-rings
• Glide rings
• Rubber moving parts
• Foam rings
• Rear shock mounting hardware
and main seals
• Upper tubes (stanchions)
• Stripped threads/bolts
(aluminium, titanium, magnesium
or steel)
•
•
•
•
•
•
•
•
•
•
•
Brake sleeves
Brake pads
Chains
Sprockets
Cassettes
Shifter and brake cables (inner
and outer)
Handlebar grips
Shifter grips
Jockey wheels
Disc brake rotors
Wheel braking surfaces
•
•
•
•
•
•
Bottomout pads
Bearings
Bearing races
Pawls
Transmission gears
Tools
This warranty shall not cover damages caused by the use of parts of different manufacturers.
This warranty shall not cover damages caused by the use of parts that are not compatible, suitable and/or
authorised by SRAM for use with SRAM components.
This warranty shall not cover damages resulting from commercial (rental) use.
Copyright © SRAM 2009, LLC
Publ. No. GEN.0000000002022 · Rev. A
Released June 2009
For exploded diagram and part number information, please refer to the Spare Parts Catalog available on our web site at www.sram.com.
For order information, please contact your local SRAM distributor or dealer.
Information contained in this publication is subject to change at any time without prior notice. For the latest technical information, please visit our website at www.sram.com.
Your product‘s appearance may differ from the pictures/diagrams contained in this catalog.
This publication includes trademarks and registered trademarks of SRAM Corporation designated by the symbols ™ and ®, respectively.
Product names used in this document may be trademarks or registered trademarks of others.
2
Technical Manual Gear Hub Systems 2010 · Copyright © SRAM 2009, LLC
TABLE OF CONTENTS
GEAR HUB SYSTEMS
GEAR HUBS AND SHIFTERS
i-MOTION
®
9
i-MOTION
®
3
SRAM
®
Torpedo
®
Singlespeed
DualDrive
™
SRAM
®
S7
SRAM
®
P5
CARGO
5
27
49
58
69
77
85
92
101
SRAM
®
P5 Cargo
SRAM
®
T3
Sparc
®
GEAR HUB SYSTEM COMPONENTS
Brake Lever
i-LIGHT
™
– Dynamo Hubs
Power Chain
™
SRAM Komfy
™
– Hydraulic Disc Brake
See Technical Manual AVID – „Juicy
®
5“
Technical Manual Gear Hub Systems 2010 ·
GEN.0000000002002 · Rev. A
108
110
114
3
4
Technical Manual Gear Hub Systems 2010 · Copyright © SRAM 2009, LLC
i-MOTION
®
9
TECHNICAL DATA / ASSEMBLY REQUIREMENTS
L
OLD
3.2
A
3.2
2.2
A
103.6
HR
M 10x1
M 10x1
3.5
3.5
F
1
F
2
CL
1
Ø 7.6
56.3
94.8
Version with back pedal brake
/
2
OLD
i-MOTION 9 with back pedal brake
Speeds
Brake
Over Locknut Dim., OLD
Length, L
Ends Diameter
Holes
Hole Diameter, DS
Hole Ref. ø, HR
Overall
1st gear
2nd gear
9
With back pedal brake
135 mm
186 mm
M 10x1
min. 4 mm / max. 10 mm
36 or 32
2.8 mm
93.6 mm
F
1
= 26.5 mm / F
2
= 31.5 mm
340 %
0,542
0,621
0,727
0,853
1,000
1,172
1,375
1,611
1,844
48.8 mm
1.73 – 1.90
1
i-MOTION 9 disc brake compatib.
9a
Adaptor for disc brake
135 mm
186 mm
M 10x1
min. 4 mm / max. 10 mm
36 or 32
2.8 mm
93.6 mm
F
1
= 26.5 mm / F
2
= 31.5 mm
DS
i-MOTION 9 without brake
9
without
135 mm
186 mm
M 10x1
min. 4 mm / max. 10 mm
36 or 32
2.8 mm
93.6 mm
F
1
= 26.5 mm / F
2
= 31.5 mm
Dropout Width Dim., A
G
E
T
R
I
E
B
E
N
A
B
E
N
Speichen
Achse
Flange Dist. to
1
/
2
OLD
Gangsprung
14 %
17 %
17 %
17 %
17 %
17 %
17 %
14 %
48.8 mm
min. 1.73
1
3
1
Übersetzung
3rd gear
4th gear
5th gear
6th gear
7th gear
8th gear
9th gear
Chainline, CL
Ratio
Dimensions
Sprocket
Shifter
Disc Brake
Hand brake lever
Tandem
Weight
Mat. Hub shell
Surface
Kette
48.8 mm
min. 1.73
1
3
1
/
2
" x /
8
" and /
2
" x /
32
"
1
/
2
" x /
8
" and /
2
" x /
32
"
1
/
2
" x
1
/
8
" and
1
/
2
" x
3
/
32
"
Kompatibilität
18 / 19 / 20 / 21 / 22 teeth
i-MOTION 9 IBS SL and i-MOTION 9 SL
—
—
2,400 g
Aluminum
Satin matt "Lux" anodized
18 / 19 / 20 / 21 / 22 teeth
6 holes
Disc brake compatible
1,960 g
Aluminum
Satin matt "Lux" anodized
18 / 19 / 20 / 21 / 22 teeth
—
—
1,960 g
Aluminum
Satin matt "Lux" anodized
Not suitable for tandems, transport bicycles
or similar
Finish
Technical Manual Gear Hub Systems 2010 ·
GEN.0000000002002 · Rev. A
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin