Nissan Atleon air suspension 4.5251_istr_mont_ENG_VB_ECO.pdf

(3725 KB) Pobierz
VB ref.
1521013004
Rear integrative pneumatic suspension for
8
This leaflet is purely for illustrative purposes and may not reflect correctly the supplied parts. The manufacturer re-
serves to amend the contents of it whenever necessary and without notice.
4.5251E-IM-VB-ECO
Distributed by:
VB air suspension
Varsseveld-Holland
Frankenweg 3
Varsseveld-Holland
NISSAN Atleon
120.35 - 35.13
ENG
INSTALLATION INSTRUCTIONS
PACKAGE CONTENT
Remove original plate on differential gearbox and
replace with provided one, lock with original
screws.
Remount previously disconnected parts on left
suspension support plate as shown in picture.
M8 (4X)
M8x25 (2X)
M10x25 (6X)
Grommet
(2X)
M10 (6X)
Ø10x20 (6X)
Right suspension
(1x)
Left suspension
(1x)
Crossbar (1X)
Ø10x20 (6X)
Ø8x15 (4X)
Spacer (1X)
Regulation plate (1X)
3
SMALL HARDWARE KIT
RILSAN KIT PIPE composed by:
•
Red pipe (6m)
•
Black Pipe (6m)
Clips kit Composed by:
•
Plastic clips (20x)
Pressures sticker (1X)
Pneumatic system instructions (1x)
4
5
Drive Way
BEFORE OPERATING ANY MODIFICATION MEASURE THE
BRAKE REGULATOR SPRING EXTENSION !
LEFT SIDE
Place provided spacer (40mm)between chassis and brake pipe support, after locking brake regulator on
new position.
Link again brake regulator spring on the differential gearbox, increase original lenght by 10-15 mm, using regula-
tion plate holes.
1
Place the vehicle in a hole or bridge, to operate
SAFE and comfortably.
2
Remove the rebound end pads and give them
to the end user.
WARNING : For the execution of the pneumatic system, please strictly refer the specific given instructions. In fact , the system may vary according to the chosen
version (manual, self levelling or electrical); so than the instructions for the pneumatic system are stated in the apposite handbook enclosed at the purchased kit.
IMPORTANT: do NOT use liquid Teflon®, hemp, paints etc. .In case of problem and/or information, contact our technical office. In case you fail to comply at this indi-
cations, VB-Airsuspension isn’t responsible for eventually damages derivates. For further information contact us.
2
7
BRAKE REGULATOR MODIFICATION INSTRUCTION
RIGHT SIDE
LEFT SIDE
3
Mount
right
suspension as shown in picture,
insert zinc plated spacer between suspension
and locking group.
4
Mount
left
suspension as shown in picture,
insert zinc plated spacer between suspen-
sion and locking group.
1
IMPORTANT : Before remove the brake regulator,
measure the brake regulator spring extension to
be able to increase its lenght by 10-15 mm.
Unscrew brake regulator from original support
plate as shown in picture.
2
NOTE : To remove original support plate unscrew
brake regularor from plate,it is not necessary to
disconnect hydraulic brake pipe from control val-
ve. If this come necessary due to other obstacles :
BLEED HYDRAULIC BRAKE SYSTEM, IF NECES-
SARY INTEGRATE AS NISSAN SPECIFICATION.
LEFT SIDE
Drive Way
LEFT SIDE
Drive Way
5
Unscrew front locking nuts from rear leaf
spring. To place suspension may be necessary
extract a little locking clamp.
6
Place suspension between axle and chassis. Fit
leaf spring locking clamp in suspension plate
holes.
Lock again leaf spring pack.
6
3
RIGHT SIDE
Senso di marcia
Drive Way
RIGHT SIDE
RIGHT SIDE
7
Lock the suspension on chassis as shown in
picture with provided screws, nuts and wa-
shers.
8
Repeat position from 1 to 7 for other side of
vehicle.
Fit RILSAN pipe on pipe fitting::
•
Red for right side
•
Black for left side.
11
Fix brake regulator previously removed on
cross-bar support plate.
Suspension correctly mounted.
12
RIGHT SIDE
RIGHT SIDE
Senso di marcia
Drive Way
Senso di marcia
Drive Way
9
Mount the cross-bar as shown in picture, lock
with provided screws, nuts and washers.
10
Lock the crossbar on both sides. Proceed in and
remount brake regulator. Pay attention to spe-
cific intructions.
4
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin