NVIP_2DN7018CZ_2P_SHORT_1.0_EN_PL.pdf

(5252 KB) Pobierz
U s e r ’s m a n u a l
(short)
NVIP-2DN7018CZ-2P
NVIP-2DN7018CZ-2P 1.0 version - User’s manual (short)
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
•
•
Electromagnetic compatibility EMC 2004/108/EC.
Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2002/96/EC
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic
Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will
help to prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2002/95/EC
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous
substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our products have
been tested and do not contain hazardous substances whose exceeding limits could have negative
impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN
USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES
NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE
CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR
THE RESULTS OF SUCH AN ACTION.
All rights reserved © AAT Holding sp. z o.o.
2
NVIP-2DN7018CZ-2P 1.0 version - User’s manual (short)
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE
PERSONNEL MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer
is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself
as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
10.
Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Information
Due to the product being constantly enhanced and optimized, certain parameters and functions described in the
manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com
website in order to access the newest manual.
Data included in the following user’s manual is up to date at the time of printing. AAT Holding Sp z o.o. holds
exclusive rights to modify this manual. The producer reserves the rights for device specification modification
and change in the design without prior notice.
All rights reserved © AAT Holding sp. z o.o.
3
NVIP-2DN7018CZ-2P 1.0 version - User’s manual (short)
TABLE OF CONTENTS
TABLE OF CONTENTS
..................................................................................................... 4
1. FOREWORD INFORMATION
................................................................................... ..5
1.1. General Characteristics ........................................................................................ 5
1.2. NVIP-2DN7018CZ-2P tech specification ....................................................... ...6
1.3. Camera dimension ........................................................................................... ...7
1.4. Package contents............................................................................................... ...8
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
................................. 9
2.1. Description of connectors and control tools ........................................................ 9
2.2. Starting the IP camera........................................................................................ 10
2.3. Initial configuration via the Web browser ......................................................... 11
3. NETWORK CONNECTION UTILIZING WEB BROSWER
................................ 12
3.1. Recommended PC specification for web browser ............................................. 12
3.2. Connection with IP camera via the Internet Explorer ........................................ 12
3.3. Connection with IP camera via other browsers .................................................. 13
4. WWW INTERFACE - WORKING WITH IP CAMERA
......................................... 16
4.1. Displaying live pictures. ..................................................................................... 16
5. ELECTRIC CONNECTORS AND ACCESORIES
................................................. 18
5.1. Connecting power supply to the camera. .......................................................... 18
5.1. Connecting alarm input and output .................................................................... 18
5.2. SD card installation ........................................................................................... 19
6. RESTORING FACTORY DEFAULTS
..................................................................... 20
6.1. Restoring software factory defaults .................................................................... 20
6.2. Restoring hardware factory defaults in IP cameras ........................................... 20
All rights reserved © AAT Holding sp. z o.o.
4
NVIP-2DN7018CZ-2P 1.0 version - User’s manual (short)
FOREWORD INFORMATION
1.
FOREWORD INFORMATION
1.1. General Characteristics
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Imager resolution: 2.0 megapixels 16:9 ratio (FullHD)
Mechanical IR cut filter
IR operation capability
Min. Illumination from 0,02 lx/F=1.2
Lens type: motor-zoom with auto iris, f=4.7~84.6 mm
Zoom: 18x, optical
Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions
Digital Slow Shutter (DSS)
Digital Noise Reduction (DNR)
Privacy zones: 5
1 BNC video output
1 Alarm input and 1 alarm output
Compression: H.264, M-JPEG
Max video processing resolution: 1920x1080
Quadruple streaming: compression, resolution, speed and quality defined individually for each
video stream
RTP/RTSP protocol support for video transmission
Pre & post-alarm functions
Hardware motion detection
Built-in webserver: camera configuration through its website
MicroSD/SDHC card support
Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,
triggering alarm output, saving file on SD/SDHC card, HTTP notification
Network protocol support : HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, Multicast, FTP, DHCP,
DDNS, NTP, RTSP, RTP, UPnP, SNMP, QoS,
Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
Power supply: 24V AC, 12VDC, PoE (Power over Ethernet)
All rights reserved © AAT Holding sp. z o.o.
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin