MR416LAGUNA6(1).pdf

(471 KB) Pobierz
6
Sealing and soundproofing
65A
OPENING ELEMENT SEALING
WINDOW SEALING
SOUNDPROOFING
66A
68A
X91
JANUARY 2009
"The repair methods given by the manufacturer in this document are based on the technical
specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the manufacturer in the
production of the various component units and accessories from which his vehicles are
constructed."
All copyrights reserved by Renault.
The reproduction or translation in part of whole of the present document, as well as the use
of the spare parts reference numbering system, are prohibited without the prior written
consent of Renault.
Edition Anglaise
© Renault s.a.s 2008
LAGUNA III - Section 6 ContentsPage
LAGUNA III - Section 6
Contents
Page
65A
OPENING ELEMENT SEALING
Door sealing film: Removal -
Refitting
Front side door seal:
Removal - Refitting
Sunroof seal: Removal -
Refitting
65A-1
65A-5
65A-8
66A
WINDOW SEALING
Front side door glass run
channel: Removal - Refitting
Front door side exterior
weather strip: Removal -
Refitting
Rear side door exterior
weather strip: Removal -
Refitting
Glass run channel in rear
side door: Removal -
Refitting
66A-1
66A-6
66A-8
66A-9
68A
SOUNDPROOFING
Bonnet soundproofing:
Removal - Refitting
Bulkhead insulating material:
Removal - Refitting
68A-1
68A-2
OPENING ELEMENT SEALING
Door sealing film: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Remove the front side door trim (see
Front side
door trim: Removal - Refitting)
(72A, Side opening
elements trim).
B91 or K91
a
or remove the rear side door trim (see
Rear side
door trim: Removal - Refitting)
(72A, Side opening
elements trim).
B91 or K91
65A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
front door
122895
rear door
122893
a
Start removing the sealing film at the upper section
(1) .
65A-1
OPENING ELEMENT SEALING
Door sealing film: Removal - Refitting
65A
D91
a
Carefully remove the mastic bead from the door box
section around the edges of the sealing film.
Note:
If the mastic bead offers too much resistance,
use a hot air gun set to approximately
100˚C
held
approximately
20 cm
away from the sealing film
to ease its removal.
REFITTING
I - REFITTING PREPARATION OPERATION
a
parts always to be replaced: Door sealing film
(60,03,02,10).
Note:
Remove the adhesive residue from the door box
section by applying wide masking tape over the
bonding area. Pull gently on the masking tape to
remove any adhesive residue.
Clean the door frame door box section using a
lint-free cloth dipped in heptane.
134946
WARNING
The door must be clean (free of dust, grease,
anti-adhesive products), with no trace of impuri-
ties and no condensation. The area of the inner
door panel where the film is applied must be
painted completely.
Adhesive surfaces should be at a minimum tem-
perature of
15˚
in order for the film to adhere pro-
perly to the door.
II - REFITTING OPERATION FOR PART
CONCERNED
a
Remove the paper protecting the sealing film mastic
bead.
134947
a
Start removing the sealing film at the upper section
(1) .
Note:
Do not touch the mastic bead.
65A-2
OPENING ELEMENT SEALING
Door sealing film: Removal - Refitting
65A
B91 or K91
front door
D91
134946
122895
rear door
134947
a
Offer up the sealing film without forcing it, bringing it
into contact with the areas shown (2) .
122893
a
Offer up the sealing film without forcing it, bringing it
into contact with the areas shown (2) .
a
Position the sealing film correctly around the outside
edge without applying any pressure.
a
Firmly attach the sealing film around its entire edge.
65A-3

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin