Techbe1-be3l04.pdf

(1130 KB) Pobierz
Edition
01
02
03
04
Modification
Documentation creation by association of the BE1 and BE3 technical documentation in one
documentation
Audio modification on BE3
Documentation correction on page 19
Flow chart and visual inspection modification ;Battery test ; new fault codes and a mandatory
equipment list; Audio modification for BE1 and BE3
Date
09/03/2000
06/06/2000
13/06/2000
05/10/2000
Explanation of the modifications since the last edition
Improvement
Audio improvements on BE1 and
BE3 products
Correction
Replace the audio amplifier by an Analog
Device amplifier if the solder modification
does not solve the problem
Comments
Battery test
FUNCTION:
Author
Pilot Repair Centre
Approbation 1
Pilot Repair Centre
Approbation 2
Technical Assistance
DATE:
VISA:
ED
04
09/10/00 REPAIR DOCUMENTATION BE1 and BE3 Level 2
BE 1/BE3
1/46
All rights reserved.Passing on and copying of this document, use and communication of its contents are not permitted without
authorization
CONTENTS
1) LEVEL 2 REPAIR PROCESS
2) TEST & VISUAL INSPECTION
3) DISASSEMBLY OF THE PRODUCT
4) HARDWARE UPGRADING
5) REPAIR
6) ASSEMBLY OF THE PRODUCT
7) STICKERS
8) CUSTOMIZATION SOFTWARE DOWNLOADING
9) FINAL TEST
9.1 Functionnal test
9.2 Measurements
APPENDIX 1 FAULT CODES
APPENDIX 2 EQUIPMENT FOR LEVEL 2 REPAIR CENTRE
3
4
8
20
24
27
39
41
42
42
42
43
45
ED
04
11/10/00 REPAIR DOCUMENTATION BE1 and BE3 Level 2
BE 1/BE3
2/46
All rights reserved.Passing on and copying of this document, use and communication of its contents are not permitted without
authorization
1) LEVEL 2 REPAIR PROCESS
start
Test + visual inspection
See § 2
Disassembly
See § 3
Hardware upgrading
See § 4
Level 2 repair
See § 5
Final assembly
See § 6
Rear casing is
changed ?
N0
YES
Complete sticker printing
See § 7
Customization software downloading
OK
See § 8
NOK
To a Level 3 repair centre
See § 7
Software technical level sticker
Final test
OK
See § 9
NOK
end
end
ED
04
09/10/00 REPAIR DOCUMENTATION BE1 and BE3 Level 2
BE 1/BE3
3/46
All rights reserved.Passing on and copying of this document, use and communication of its contents are not permitted without
authorization
2) TEST & VISUAL INSPECTION
ALL these verifications must be done on ALL products coming back
in a LEVEL 2 after sales repair centre .
a)
b)
Check the aspect of the rear casing and the antenna
Humidity sticker : a humidity sticker is present on some
BE1 terminals on the shielding that can be seen on the rear
casing side, without openning the handset . Check the state of
the sticker as shown below :
Sticker of a good terminal
Sticker of a terminal dived in water
This terminal is out of the warranty
c)
d)
e)
Check J904 , the charge connector (corrosion ,contacts)
Check the SIM latch right functioning
Insert a SIM card and check the holding of the SIM latch
Plug a good battery and switch on the handset : check the
charging icon animation on the display, check the holding of
the product on the desk top charger.
04
09/10/00 REPAIR DOCUMENTATION BE1 and BE3 Level 2
BE 1/BE3
4/46
f)
ED
All rights reserved.Passing on and copying of this document, use and communication of its contents are not permitted without
authorization
g)
When the handset with its battery comes back to be
repaired, you must measure the voltage and the Thermistor
value as shown below.
1
2 3 4 5
6
1 2 3 4 5 6
NI MH Battery
With a multimeter:
•
Measure the voltage between pin 1 and pin 6 (if < 2.9 V, the battery
is NOK)
•
Measure the Thermistor value between pin 5 and pin 6 for Ni MH
battery
•
Measure the Thermistor value between pin 4 and pin 6 for Lithium
battery (the Thermistor value must be 100 k? at 25 °C)
ED
04
09/10/00 REPAIR DOCUMENTATION BE1 and BE3 Level 2
All rights reserved.Passing on and copying of this document, use and communication of its contents are not permitted without
authorization
ASSEMBLED IN FRANCE
Lithium battery
ALCATEL
POWER PACK
ASSEMBLED IN FRANCE
ALCATEL
POWER PACK
BE 1/BE3
5/46

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin